More often than not when you find yourself spraying latex you’ll be painting interiors of homes It is usually very common to make use of airless sprayers for this purpose. Nevertheless, airless sprayers don’t provide the same high quality of end which you can achieve with an HVLP Spray Gun. Additionally, an HVLP spray gun is more efficient at applying coating to a product’s surface. The downside to an HVLP spray gun is that it will likely be slower than an airless at finishing a given project. Ultimately, in case your predominant goal is achieving a high high quality end an HVLP spray gun is what you’ll most likely want to use.
Challenges of using HVLP spray gun with latex paint
HVLP spray guns use a high volume of air at low pressure to atomize (break up) coating. The low pressure allows them to use less paint and be more environment friendly at applying a coating to a product surface. However, the low pressure that HLP spray gun makes use of could make it harder to interrupt up thicker coatings, including latex paints. To be able to successfully spray latex paint with an HVLP spray gun, a few things will need to be considered.
You’ll need to make use of a high quantity air cap (high CFM) – high quality HVLP spray guns will come with a variety of setups for the air cap as well because the fluid nozzle. The higher the quantity of air and air cap uses, the better will probably be at being able to atomize heavier bodied coatings like latex paint.
If you will be utilizing a turbine pushed HVLP spray gun you will want to use a multistage turbine. The more levels which you could afford to your turbine unit, the greater ability the unit can have in being able to spray latex paint. If you’re considering between an HVLP spray gun and a turbine unit for latex painting projects, you may learn in regards to the differences between the 2 here.
Use a big fluid nozzle- For a pressure fed HVLP Spray Gun you will normally need to use at the least a 1.eight MM Fluid Nozzle. For a Gravity Fed HVLP Spray Gun you will typically want not less than a 2.0 or higher to be able to get the Latex Paint to flow. The big fluid nozzle will allow for the latex paint to circulate, smaller fluid nozzles will typically be hard to get Latex paint to movement adequately.
Thinning-you’ll most probably should thin the latex paint to be able to get it to adequately atomize. This is particularly true if your utilizing a gravity fed HVLP Spray gun. You need to make sure that to use the manufacturer’s beneficial thinner and only thin it the minimal amount needed to get it to adequately spray.
If you do not want to use thinner, you’ll need to consider utilizing a pressure fed HVLP spray gun – pressure fed weapons are available for HVLP spray weapons which are fed by an air compressor. They’ll allow thicker coatings to be able to be equipped to the gun effectively and provides higher control of the amount of coating you are supplying at a given time which can help in achieving higher atomization regardless of the heavy bodied latex paint. You can learn more about pressure vs gravity vs suction fed spray guns here.
When an HVLP spray gun is right for spraying latex paint
When your major goal is achieving a quality end like when painting cabinets or trim
When you have smaller areas to be painted that will not require a big volume of paint to cover the surface
When you need to hold Overspray to a Minimum
Alternate options to using an HVLP spray gun with latex paint
If you wish to be able to keep up high production but still achieve a finer end, you could possibly probably use an airless paint sprayer with a fine end tip. A Fine finish tip allows for higher atomization than a normal airless tip although won’t yield the same finish that an HVLP spray gun will.
Conclusion
should you’re looking at a project will require a fine end and requires the application of latex paint and HVLP spray gun will be the ultimate answer for you. To achieve the most effective outcome attainable, you want to use a high quantity CFM air cap, thin the fabric an appropriate quantity, consider utilizing a pressure fed system especially if you’ll be using a compressor fed HVLP spray can, and if you may be using a turbine driven HvLP spray gun you’ll want to use a multistage system. By following the following pointers, you can be able to achieve a quality finish with your latex paint project. For options on compressed air spray guns that may be preferrred on your project you may contact us today
Should you loved this post and you would want to receive much more information concerning Latex spuiten muur i implore you to visit our own internet site.