More often than not if you end up spraying latex you will be painting interiors of homes It’s typically quite common to use airless sprayers for this purpose. Nonetheless, airless sprayers do not provide the identical high quality of end which you could achieve with an HVLP Spray Gun. Additionally, an HVLP spray gun is more efficient at making use of coating to a product’s surface. The downside to an HVLP spray gun is that it is going to be slower than an airless at finishing a given project. Ultimately, in case your major goal is achieving a high high quality finish an HVLP spray gun is what you’ll almost certainly wish to use.
Challenges of using HVLP spray gun with latex paint
HVLP spray weapons use a high quantity of air at low pressure to atomize (break up) coating. The low pressure allows them to use less paint and be more efficient at applying a coating to a product surface. Nevertheless, the low pressure that HLP spray gun makes use of could make it harder to break up thicker coatings, including latex paints. To be able to successfully spray latex paint with an HVLP spray gun, a few things will have to be considered.
You will need to make use of a high volume air cap (high CFM) – high quality HVLP spray guns will come with a variety of setups for the air cap as well because the fluid nozzle. The higher the amount of air and air cap makes use of, the better it will be at being able to atomize heavier bodied coatings like latex paint.
If you’ll be utilizing a turbine driven HVLP spray gun it would be best to use a multistage turbine. The more stages you can afford in your turbine unit, the greater ability the unit may have in being able to spray latex paint. In case you are considering between an HVLP spray gun and a turbine unit for latex painting projects, you may study in regards to the differences between the 2 here.
Use a large fluid nozzle- For a pressure fed HVLP Spray Gun you’ll often need to use not less than a 1.8 MM Fluid Nozzle. For a Gravity Fed HVLP Spray Gun you will typically need at the least a 2.zero or higher to be able to get the Latex Paint to flow. The massive fluid nozzle will allow for the latex paint to flow, smaller fluid nozzles will typically be hard to get Latex paint to stream adequately.
Thinning-you’ll most certainly should thin the latex paint to be able to get it to adequately atomize. This is particularly true if your utilizing a gravity fed HVLP Spray gun. You need to make sure that to make use of the manufacturer’s beneficial thinner and only thin it the minimal quantity needed to get it to adequately spray.
If you don’t want to use thinner, you’ll want to consider using a pressure fed HVLP spray gun – pressure fed weapons are available for HVLP spray weapons which can be fed by an air compressor. They’ll enable thicker coatings to be able to be equipped to the gun effectively and give better control of the quantity of coating you might be supplying at a given time which will help in achieving better atomization despite the heavy bodied latex paint. You can study more about pressure vs gravity vs suction fed spray weapons here.
When an HVLP spray gun is right for spraying latex paint
When your main goal is achieving a top quality finish like when painting cabinets or trim
When you have smaller areas to be painted that will not require a big volume of paint to cover the surface
When it’s worthwhile to preserve Overspray to a Minimal
Options to using an HVLP spray gun with latex paint
If you want to be able to maintain high production but still achieve a finer finish, you may probably use an airless paint sprayer with a fine finish tip. A Fine end tip allows for higher atomization than a normal airless tip though will not yield the same finish that an HVLP spray gun will.
Conclusion
for those who’re taking a look at a project will require a fine end and requires the application of latex paint and HVLP spray gun may be the ideally suited resolution for you. To achieve one of the best end result doable, you wish to use a high quantity CFM air cap, thin the fabric an appropriate amount, consider using a pressure fed system especially if you can be utilizing a compressor fed HVLP spray can, and if you’ll be utilizing a turbine pushed HvLP spray gun it would be best to use a multistage system. By following the following pointers, you’ll be able to achieve a quality end together with your latex paint project. For options on compressed air spray guns that is perhaps preferrred on your project you possibly can contact us at present
In case you have almost any queries relating to wherever in addition to how you can work with Latex spuiten, you possibly can e-mail us in our own web site.